2014-07-30

Looking for Moorage

We are trying to find a place to moor the boat. While our mast raising system works, it is still a pretty labor intensive operation to make the boat ready for launch and put it back on the trailer at the end of the day. It would be much better if it was in the water for the summer. Or alternately in dry storage on land, with the mast up.

Unfortunately, every slip in the north end of Lake Washington seems to be full. Ideally, we'd find a slip for about $200 a month, five minutes from our house, for May through September each year. And pigs can fly.

We went out and looked at a slip on Portage Bay, between Lake Union and Lake Washington. We also looked at using dry storage at Sail Sand Point. The Sail Sand Point dry storage only allows hand launch boats. Ours is a little too big for that. There is another dry storage place in Bellevue, but it is undergoing maintenance and closing for a time.

2014-07-27

Back on Land

After another fabulous day, we pulled her out.

Trailer Winch Repair

Winch with new strap in place
Winch with new strap in place

While the boat was in the water, it was time to repair the trailer winch. The winch had a 3/16" metal cable with an eye and hook at the end. The cable at the eye had broken. This was temporarily fixed by tying a knot in the cable around the hook, which was enough to get the boat into the water, but not good for the long term.

We decided to replace the cable with a hitch strap. At times that cable has a fair amount of pressure being applied to it. If the cable ever snaps because it is old, a whipping cable could damage something nearby, such as fiberglass or a person's nose. Also, it is likely that the eye repair would fail again, causing other problems at an inopportune time.

We bought a new 2" x 25' 10,000 pound winch strap at North Lake Marina in Kenmore ($19.95 + $1.90 tax). Possibly overkill for what we are doing, but Greg really likes to have overspec hardware.

Greg removed the cable from the Fulton two-speed winch with a pair of pliers. But putting the new cable strap on wasn't going to be easy. Normally for a winch strap, there is a bolt that you thread the end of the strap over. However, this winch was made for a cable, not a strap, and there were no holes lined up on both sides of the winch to put a bolt through. Greg drilled a 3/8" hole through the side of the winch. He then acquired a 4.5" x 3/8" galvanized grade 8 bolt, two fender washers, and a nut at McLendon Hardware in Woodinville. (McLendon has a better selection of hardware than Home Depot or Lowe's) Total: $1.85 + $0.18 tax. Turns out a 3.5" bolt would have been long enough, but the purchased bolt worked without binding to anything.

With the new hole drilled, the bolt was threaded through the winch, two fender washers and the end of the strap. The new strap works great.

2014-07-26

She Floats! Putting the Catalina 22 in the Water

First launch was a success! The day was not without its share of hiccups, which we've been warned is standard operating procedure, but it was a great day nonetheless.

Not only was it our first attempt at launching our new-to-us boat, it was our first attempt at launching any boat...Ever. We were of course a little nervous. We had gone over all the things we'd need to do the night before and made lists. We got up super early, dragging ourselves and the kids out of bed, excited by the prospect of a fun day out on the water, a new adventure for us all. We were blissfully unaware of all the things we didn't yet know!

Once the trailer was hooked up to the car, we drove down to the boat ramp, arriving before 6:30am, to make sure we'd be able to get our choice of parking spots from which to step the mast. Trailering the boat with our Caravan is pretty much right on the limit of what it can handle, but as the trip is less than 3 miles from house to boat ramp, it's very doable. Backed in, wheels chocked, ladder set up and cabin open. We set about the task of raising the mast. With the mast propped up and walked back, the mast bolt went in without any trouble. We started hooking up the gin pole, but soon realized we couldn't get the jib halyard to budge. With the mast head now well out of reach from the boat or the ground, we scratched our heads for a bit before realizing the 2 inch strap securing the gin pole to the mast had been accidentally wrapped around the jib halyard as well, underneath the mast and out of sight!

With the jib halyard freed, the mast went up relatively easily, alternately cranking, then stopping a couple of times mid-raise to free shrouds that were determined to get caught on each and every protruding cleat, cam or bolt on the deck. With our mast raising system, only the two forward shrouds and the rolling furler jib (which incorporates the forestay) have to be removed and reconnected/retensioned. We'd decided that for our first run, we'd just get the boat off the trailer and motor over to a nearby public dock and hang out, and tie up for the night in another nearby marina's guest moorage. With the mast up and secure, we started loading the rest of the things we'd need for our day out. Water, check. PFDs, check. Lines, check. Keel raised, check. Gas can.......gas can......DOH! We drove off this morning without loading the gas can, kind of a must-have for motoring. We quickly unhooked the trailer from the van and Greg drove back home to get the gas can.

While waiting for Greg to return, a very nice and curious guy named Charlie came over and asked me about how we went about raising our mast. Charlie it turns out also has a Catalina 22, in the water just a few houses away from the boat launch. I showed Charlie the pieces of our mast-raising system, explained the mechanics of it and gave him my email address to send him a link to the construction details. Little did I know that just a little while later, Charlie was going to be my guardian angel!

....to be continued

Fantasia under sail
Fantasia under sail, with a Kenmore Air seaplane taking off and kayakers

2014-07-25

Connected the Trailer to the Van

Raised hitch mount
Raised hitch mount

We have a Dodge Caravan. This is not the ideal vehicle for hauling a boat around. For one, its maximum towing capacity is 3500 pounds, which is near what we are hauling around. We probably wouldn't want to tow the boat across country, but it is fine for taking it a few miles around here.

Second, it is front wheel drive. Towing a vehicle usually works best with a rear wheel (or four-wheel) drive vehicle.

Third, is is close to the ground, especially the trailer hitch.

When we went to put the trailer on the van, we found that the straight hitch mount we had put the trailer too close to the ground. We needed one that brought the trailer up about four inches. We headed off to our local U-Haul for a new hitch mount. After we got there, we realized that the hitch mount that raises the trailer up four inches is also the one that lowers it four inches...you just mount the ball on the other side. It just so happened we had one of those at home with the ball on the wrong side for what we needed.

After spending half an hour with some monkey wrenches, we got the ball off and moved to the other side and remounted. Problem solved! When connecting to the trailer, it's at the right level now.

2014-07-22

Sanded the Teak

Sanded down the teak. This is a job in progress and will continue over time.

Catalina 22 teak hand holds, nicely sanded
Catalina 22 teak hand holds, nicely sanded

2014-07-20

Cleared the Drains on the Catalina 22

The Catalina 22 drains. Clearing these from time to time is necessary.

The Catalina 22 has two drains in the forward part of the cockpit that empty into plastic pipes below deck. These then empty through a seacock into the volcano under the boat. The holes in the drains are fairly big, and quite a lot of debris accumulates in these plastic pipes. One side was completely clogged, and the other was mostly clogged, keeping water in the cockpit. We detached the hoses and cleaned them out.

2014-07-19

Raised the Mast on the Catalina 22

We tried out our mast raising system. With some problems to solve, it worked! In the picture you can see the gin pole attached to the front of the mast.

Catalina 22 with the mast raised
Sandi and Fantasia, with the mast raised

2014-07-18

Vessel Registration Numbers

In Washington State, each vessel that doesn't have a Coast Guard registration must be assigned a state Vessel Registration Number. Catalina 22s are too small for Coast Guard registration. The rules for the registration number are specified in WAC 308-93-145.

Section 3 says:

(3) How do I display the assigned vessel registration number on my vessel? The registration number assigned must:
(a) Be painted on or permanently attached to each side of the forward half of the vessel and easily visible for law enforcement except as allowed by subsection (6) of this section or required by subsection (9) of this section and must be on a vertical surface;
(b) Be in plain vertical block characters of not less than three inches in height;
(c) Contrast with the color of the background and be distinctly visible and legible;
(d) Have spaces or hyphens that are equal to the width of a letter other than "I" or a number other than "1" between the letter and number groupings (example: WN 5678 EF or WN-5678-EF); and
(e) Read from left to right.

The numbers on our boat are not right as there are no spaces between the groups. We will fix our numbering next year when we get the new annual registration stickers, as we cannot move the ones for this year. We will get the annual registration stickers in exactly the right spot and then put new registration number stickers on the hull with spaces or dashes.

Trailer Hitch Wiring Installed

Trailer hitch wiring installed
Trailer hitch wiring installed

The trailer hitch wiring was installed by the guy at U-Haul. It's a little awkward, as it is inside the back of the van. You have to pull the wiring through the back and lower the tailgate over it. It compresses into the gasket, but it can't be that good for the wiring.

2014-07-17

Trailer Wheels Repaired

The wheel after the repair
The wheel after the repair...the parts inside are all new

We were fortunate to know a guy who knows a guy who could come out and repair the wheels on the trailer. David and Chris completely repaired the wheels.

This is what the repair description said:

Inspected and found stuck master cylinder, leaking wheel cylinders and saturated brake shoes. Installed new brake master cylinder, both rear wheel brake assemblies, clean and repack wheel bearings with new seals. During installation one fitting broke which needed new fitting and reflared for proper seating, bleed brakes and test operations.

Cost: $843.24 + 80.11 Tax = $923.35.

2014-07-15

Trailer Hitch Installed

We had the local U-Haul install the trailer hitch. Unfortunately, the wiring wasn't in stock and had to be ordered.

Part number Product Price
HTHW Lifetime warranty 5.00
78214 Round Tube Rec. (Powder Coat) 149.95
Hitch Labor 65.00
On-Line Labor Discount -10.00
Tax 19.96
Total $229.91

2014-07-12

Catalina 22 Mast Step Repair

At the time that we bought the boat, we noted that the mast step was a little loose. The bolt and screw holding the mast step allowed the step to lift a little above the deck of the boat. Sandi had already looked into this. She wanted to put a new Mast Step Halyard Plate under the mast step anyway, giving it six points to clip various lines onto.

While we were on vacation, Sandi had ordered new stuff from Catalina Direct, including the Halyard Plate ($39.95) and a Mast Step Mounting Kit ($12.95).

She removed the mast step by unbolting it, and removing the screw that sinks through the deck into the top of the post in the cabin. We decided to use the longer of the two screws supplied as it bit into the wood a little better. Adhesive was applied and the Mast Step Halyard Plate was put down, followed by the Mast Step.

The adhesive needs five to seven days to cure, preventing us from putting the boat in the water for a while. At this point, we still do not know for sure that she floats.

Other stuff Sandi ordered:

  • Sail Tape: White Dacron 15 ft $6.53
  • Rigging Tape Self Amalgamating 19.12
  • Batten Set $24.32
  • Tension Gauge $78.00
  • West System Handy Pack Epoxy Kit $14.68
  • Teak Oil $19.95

The sail tape was needed to repair a 1" tear in the mainsail. It's a must for any sailboat maintenance kit. The batten set was ordered since two of the four mainsail battens were broken into multiple pieces. The cost of replacing just two individual battens was essentially the same as buying the entire batten replacement kit.

Warning: The new batten kit comes with fiberglass batten rods, plastic end caps, and adhesive to attach the end caps. Be very careful when handling new fiberglass batten rods—use gloves! Sandi learned the hard way that they are covered in fiberglass splinters that embedded themselves into her skin pretty much anywhere she touched them.

After getting several fiberglass splinters while gluing on the first end cap, she decided to sand them down gently with some very fine sandpaper. It worked great. No more fiberglass splinters and no need to worry when handling them to put them into or remove them from the mainsail.

We have created a page on using the Loos Tension Gauge, because the instructions may as well have been written in Rongorongo.

2014-06-22

Impulse Delivered, Becomes Fantasia

Our friend Chris brought Impulse down to us. He has a massive Ford pickup truck, which makes hauling the boat easy. He happened to be on Whidbey Island that weekend, and it was just a couple of miles out of his way.

Unfortunately, as he was bringing it in the last couple of miles, the brakes on the trailer started smoking. We weren't sure why at the time (I'll cover that in a later post). Still, it made it and got dropped in Greg's parent's driveway. Our driveway isn't conducive to parking the boat because of the steepness of it.

We had a few hours to admire our new possession before having to get ready for our vacation.

That morning we had decided on what we were going to rename the boat. Although Impulse was a good name, we had decided that Fantasia was a better name for us.

First, Sandi had just lost her mom. Her mom was a Disney Imagineer, having worked for Disney for more than 15 years. Her 15 year anniversary award was a Mickey Mouse with the sorcerer's hat and robe from the Sorcerer's Apprentice segment of the 1940 movie Fantasia. Some of Sandi's best memories growing up was going to the Disney parks with her mom, as well as one of her last. The last time Sandi had been with her mom, they went to Walt Disney World together.

Second, Greg's dad had been taking us to the Seattle Symphony for the last several years. We had heard many of the pieces from Fantasia and Fantasia 2000 being played live at various points. Since Greg's dad was helping make the acquisition of the boat possible, it seemed appropriate.

Third, I could just imagine the kids trying to bail the boat to the music of Paul Dukas's Sorcerer's Apprentice as new water came crashing over the sides.

It will take a while before the new name will be applied to the boat, so in the pictures that follow, it will still say Impulse until we can finish the renaming.

2014-06-21

Bought Impulse

Impulse Catalina 22
One of the first photos of Impulse

As just idle speculation, we mentioned to Greg's dad that "if we got a boat, could we park it in their driveway?" After trying to talk us out of it, he then started sending us links to various boats for sale. One of the prime candidates was a boat named Impulse, then on a trailer on Whidbey Island, Washington State. Actually Sandi found this boat first, and sent a link saying "this is more like what we are looking for."

On Saturday, June 14, Greg's dad went out to Whidbey Island and talked to the owner and took about 50 photos. We weren't available that day. The boat seemed in very good shape, unlike a few other that we looked at.

Sandi and Conner on Impulse
Sandi and Conner on Impulse

We went out to Whidbey Island, taking the ferry from Mukilteo. We left being the proud owners of a fine Catalina 22. At the time, our vehicle didn't have a trailer hitch, so we couldn't bring her back with us. We arrange for a friend to bring her home for us.


She came with:

  • A Calkins single axel trailer
  • 6 sails: Two mainsails, a furling jib, a regular jib, a gennaker, and a spinnaker (however, no spinnaker pole)
  • Sail bags
  • A 8 hp Johnson two cycle outboard motor J8SRLESR Rope Start Non-Tilt 20" Shaft 1990
  • A cover for the outboard
  • A Standard Horizon Eclipse DSC GX1000S 25 Watt VHF/FM DSC Marine Transceiver and antenna
  • Good cushions all round
  • Curtains
  • An anchor
  • A paddle
  • Three life vests
  • A type IV horseshoe life ring
  • An emergency kit, with flares, etc.
  • A fire extinguisher
  • An air fog horn
  • Various lines
  • Canvas winch covers
  • Parts for a mast raising system
  • A cover for the cabin when the pop-top is raised
  • Sail Cover
  • Manuals for the boat itself, the motor, the furling jib, the VHF radio, etc.
  • A chart for Puget Sound, and a guide for essential knots
  • A dodger that needs all the vinyl windows replaced
  • A Thetford Sea Farer porta-potti
  • A tiller handle cover 
  • Life lines
  • Forward hatch
  • Pop top

We went immediately to the Department of Licensing place to register it. Although we had the title for the boat, we discovered that we didn't get the title for the trailer. The reason was that it had just been re-issued to the previous owner and was still in the mail. He sent it a few days later and we applied for the title after we received it.

We had done our research on the value of the boat, the trailer, and the other stuff. We had prepared three separate bills of sale: one for the boat, one for the trailer, one for all the other stuff including the outboard. There can be beneficial tax reasons for structuring it like this.

2014-06-17

Took a Look at Impulse

We went out to Whidbey Island to look at a boat. It was a disaster. It smelled inside, and had been leaking water. It was unstable on the trailer. Since we were out there, we decided to go look at Impulse. The owner wasn't home, but we could walk around it in the driveway. It looked good. It was in good shape. We decided to come back when the owner was home and could see the inside the cabin and ask some questions.

2014-06-14

Dad looks at Impulse

Impulse Catalina 22
One of the first photos of Impulse

As just idle speculation, we mentioned to Greg's dad that "if we got a boat, could we park it in their driveway?" After trying to talk us out of it, he then started sending us links to various boats for sale. One of the prime candidates was a boat named Impulse, then on a trailer on Whidbey Island, Washington State. Actually Sandi found this boat first, and sent a link saying "this is more like what we are looking for."

On Saturday, June 14, Greg's dad went out to Whidbey Island and talked to the owner and took about 50 photos. We weren't available that day. The boat seemed in very good shape, unlike a few other that we looked at.

2014-06-01

Greg's Background

Although I have never really sailed, I have pretty much always wanted a sailboat. My father had a small sailboat when I was a kid, although we didn't use it much. He, however, had dreams of owning a bigger sailboat. As a teenager, I read Chapman Piloting & Seamanship cover to cover.

After looking at the possibilities for sail boats, I decided that either I wanted a 70' sloop or ketch with staterooms and a crew, or, more realistically, a 20' to 24' sloop with a swing keel that fit on a trailer. I figured that a 20-24' boat wasn't going to capsize frequently, and would be suitable for sailing anywhere except open ocean. (Ernest Shackleton sailed a 22' boat 800 miles across the open ocean, but he really did not have a choice.)

After examining the options, I decided that a Catalina 22 was about exactly the right boat. It had sleek lines, and was easily trailerable. Some 30 years+ later my wife and I now own one.

This blog and the associated articles will chronicle our experiences with purchasing, owning, maintaining, and sailing this boat. We intend this to be a a place where we can post what we have learned as a resource to others. We will answer the stupid questions that everyone that has owned a boat before already knows, because we just asked that stupid question and had to find the answer. We will link to other content on the web that we find useful. We will also write all the standard stuff that goes into a captain's log, although we will use Gregorian dates instead of stardates, to the dismay of my Star Trek fanatic wife.

We have chosen to use a very loose definition of a yacht for the name of this blog. Some definitions of "yacht" pick an arbitrary size and state that any vessel shorter than that is a boat and not a yacht. The definition we chose is simply "a vessel used for private cruising, racing, or other noncommercial purposes". I would argue that the difference is whether it has an enclosed cabin allowing comfortable overnight accommodations. In any case, regardless of the size of the vessel, the act of having one is "yachting".

We are both pretty experienced "computer people", so where it makes sense, we will provide software tools that will help with maintaining a boat.


Welcome!

Hi!

Welcome to Greg and Sandi's Catalina 22 owner log/blog. My husband and I are excited to join the community of sail boaters, Catalina owners and other trailer sailers alike. We decided to start this blog as an updated version of the standard ship's log, and a way to share with others what we learn along the way.

First, some background...

Since we live in the greater Seattle area, we have a myriad of options for both fresh water and salt water sailing. Nearby, the San Juan Islands are recognized as a prime sailing destination both for their beauty and the protected waterways of Puget Sound. Other nearby lakes offer fresh water destinations, and Victoria, Vancouver and the Inside Passage are all within reach. We live within view of the large and beautiful Lake Washington, where I'm able to see boats out daily much of the year, even in our all too common Pacific Northwest liquid form of sunshine that some call rain. Boating in general is very popular in the region and we're looking forward to getting out on the water and creating many lasting memories with both family and friends.

Growing up in Miami, Fla., another boating mecca, I learned to sail as a child. One summer, when I was about 10, I took a sailing class with my best friend that was offered thru Girl Scouts. A couple of times each week, we attended classes and sailed dinghys around a large harbor, in between lots of large yachts moored offshore. We learned to control our little dinghys pretty quickly since a wrong move could have sent us crashing into a large and expensive yacht! The classes culminated in a day long sail south along the Miami coastline to a nearby island, circumnavigation of the island, a quick shore trip for packed lunches, and finally the long sail back home.  I think that was the day when I fell in love with sailing. Then again, it could have been the day I had a close encounter with a Florida manatee while in my dinghy.

Blackwater Sound, south of Miami, Florida
Blackwater Sound, south of Miami, Florida
Map © OpenStreetMap contributors

Shortly after learning to sail, my grandfather, who had a little property in Key Largo, bought a build-at-home sailboat kit (I don't know the make). I remember getting to work with him on it from time to time when I could go down for a visit. Once the boat was finished, he started taking it out, but my grandmother said he wouldn't put the sails up without me along because he'd never learned to sail! Usually, he'd just motor around with it. I remember one time I got in trouble at home and was grounded on a weekend I'd been planning to go down to Key Largo. I packed my bag, snuck out and started walking towards Key Largo, running away from home, to go sailing with him. That's about 60 miles I was planning to walk, and I was around 12 years old.

Diego Garcia, in the Indian Ocean
Diego Garcia, in the Indian Ocean Map © OpenStreetMap contributors

We sailed together on and off for several years, all around Key Largo but mainly in Black Water Sound. In my mid teens, I got busy with school and friends and didn't spend as much time with my grandparents. But at age 19, I had the good fortune to spend a year working on a tropical island in the middle of the Indian Ocean with both Laser and Catalina sailboats available to rent very cheaply, along with some pretty amazing beaches, fishing, and snorkeling. The sailing club on the island put on races regularly, and I spent many of my days off either racing in a Laser or cruising one of their Catalina 22s around the large protected lagoon. It was there that I fell in love with the Catalina 22.